Vaisala DMP248 Manual de servicio Pagina 87
- Pagina / 145
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
APPENDIX 1 SERIAL COMMANDS__________________________________________________________
VAISALA _________________________________________________________________________ 81
APPENDIX 1 SERIAL COMMANDS
APPENDIX 1 81
A
UTO-CALIBRATION COMMANDS 83
DRYCAL Defining the frequency of auto-calibration cycles 83
DCAL Forced auto-calibration 84
A
NALOGUE OUTPUT COMMANDS 84
AMODE Setting the analogue outputs 84
ASEL Selecting the scaling the analogue output quantities 85
ASCL Scaling the analogue outputs 86
C
ALIBRATION COMMANDS 87
CRH Relative humidity calibration 87
CT Temperature calibration 87
ACAL Calibrating the analogue outputs 88
L Outputting linear correction coefficients 88
LI Entering linear correction coefficients 89
O
UTPUT VIA THE SERIAL BUS 89
R Starting the measurement output 89
S Stopping the measurement output 90
SEND Outputting a reading once 90
DSEND Outputting readings of all connected transmitters once 90
ERRS Outputting error messages 91
ECHO Turning the serial interface echo ON/OFF 91
INTV Setting the output interval for the RUN state 91
FORM Setting the output format 92
FTIME Adding time to output 93
FDATE Adding date to output 94
SERI Serial bus settings 95
UNIT Selecting the output units 95
ADDR Setting the transmitter address 96
RESET Resetting the transmitter 96
O
PERATION MODES 97
SMODE Setting the serial interface 97
OPEN & CLOSE 97
O
THERS 98
ITEST Testing the analogue outputs 98
PRES Setting the pressure for pressure compensation and ppm calculations 99
XPRES Setting the pressure for pressure compensation and for ppm calculations temporarily 100
CDATE Entering calibration date 100
DATE Setting the date 100
TIME Setting the time 101
VERS Name and version of the programme 101
? Outputting the transmitter settings 101
?? Outputting the transmitter settings also in POLL mode 102
Setting and activating the outputs with menu commands 135
Setting and activating the outputs using an RS line 136
The commands function as described when the serial interface is in full-duplex mode
and echo is on. All commands except FORM can be given in either capital or small
letters.
In the commands <cr> means carriage return, <lf> line feed and <ht> horizontal
tabulation.
- OPERATING 1
- Table of contents 3
- GENERAL INFORMATION 7
- PRODUCT DESCRIPTION 9
- FIGURE 2-2 shows the DRYCAP 11
- FIGURE 2-1. Now the RH 11
- Use in high pressure 12
- INSTALLATION 13
- PROBE UP 14
- DOWN 14
- Mounting; overview 15
- FIGURE 3-7 17
- R1/2 ISO 7/1 20
- VALVE OPEN 21
- PRESS TOOL 21
- VALVE CLOSED 21
- Sample cell 24
- SAMPLE CELL 25
- Grounding 27
- Connections 29
- Connection to an AC supply 30
- COMMISSIONING 31
- FIGURE 4-2 32
- RXWSXWVÕ6FDOH 33
- Spare jumpers 33
- COMMANDS 39
- LED commands 40
- Display/keypad commands 41
- Auto-calibration 42
- Forced auto-calibration 44
- Analogue output commands 44
- FIGURE 4-2) 45
- Output via serial bus 46
- Output modes 48
- Pressure compensation 50
- Setting the date 51
- Setting the time 51
- Serial commands 52
- Analogue outputs 55
- Output via the serial bus 56
- Outputting the reading once 57
- Serial bus settings 58
- Selecting the output units 58
- Resetting the transmitter 59
- Setting the serial interface 59
- OPEN & CLOSE 59
- 2 which is in POLL state 60
- CALIBRATION 61
- Using serial commands 62
- Using display/keypad commands 63
- Using LED commands 63
- Temperature calibration 65
- MAINTENANCE 73
- Adjustment using LED commands 75
- TECHNICAL DATA 79
- Temperature 80
- Relative humidity 80
- Electronics 82
- Serial interface modules 82
- Electromagnetic compatibility 83
- CHAPTER 9 OPTIONS 84
- SPARE PARTS AND 85
- ACCESSORIES 85
- APPENDIX 1 SERIAL COMMANDS 87
- Auto-calibration commands 89
- Calibration commands 93
- : 0.000 94
- FTIME Adding time to output 99
- FDATE Adding date to output 100
- SERI Serial bus settings 101
- Operation modes 103
- DATE Setting the date 106
- TIME Setting the time 107
- ?? <cr> 108
- APPENDIX 2 109
- Power supply module 110
- Technical specifications 111
- APPENDIX 3 113
- Installation 114
- Operation 114
- Network configuration 116
- RX GND TX 117
- Dual loop operation 118
- STOP mode 120
- POLL mode 121
- Specifications 122
- APPENDIX 4 123
- Dual loop wiring 129
- Current loop settings 131
- APPENDIX 5 133
- Errors after reset 134
- Errors during operation 135
- APPENDIX 6 137
- APPENDIX 7 139
- APPENDIX 8 145
Relacionado con productos y manuales para De medición, control y control Vaisala DMP248
(71 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales