Vaisala HUMICAP HMT310 Guía de usuario Pagina 82
- Pagina / 105
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
User's Guide _______________________________________________________________________
82 ___________________________________________________________________ M210619EN-E
Adjusting RH with MI70
Selecting RH in the main adjustment menu brings up a notification about
checking environment settings. Select YES to access the environment
settings before performing the RH adjustment, or NO to continue to RH
adjustment without changing the current environment settings. Select
ADJUST to access the RH adjustment options.
The following RH adjustment options are available:
- 1-point adjustment
- 2-point adjustment
- LiCl – NaCl auto
1-point RH Adjustment
Usually it is recommended to make an adjustment in two reference
humidities. If the adjustment is done by using one reference humidity (1-
point adjustment), select the reference humidity so that it represents the
measuring environment. Make the adjustment in one point as instructed
in the 2-point RH Adjustment instructions (select 1-point adjustment
instead of 2-point adjustment and follow the display instructions).
2-point RH Adjustment
Select 2-point adjustment in the RH adjustment menu and follow the
steps below:
1. Set the probe to a lower reference relative humidity. You can
follow the stabilization from the GRAPH display. Press READY
when the reading is stabilized.
2. Give the lower reference humidity value by using the arrow
buttons. Press OK.
3. Set the probe to the higher reference humidity. Press READY
when the reading is stabilized. You can follow the stabilization
from the GRAPH display.
4. Give the higher reference relative humidity value by using the
arrow buttons. Press OK.
5. To confirm the adjustment, press YES. To cancel entering the
adjustment, press NO to return to adjustment mode display
without making any changes. Note that if the difference between
the two references is less than 50 %, adjustment cannot be done.
Once confirmed, the adjustment has been carried out. Press BACK to
exit the RH adjustment mode and return to the main adjustment options.
- USER'S GUIDE 1
- Table of Contents 3
- CHAPTER 4 4
- CHAPTER 5 5
- CHAPTER 6 5
- CHAPTER 7 6
- APPENDIX A 6
- List of Figures 7
- List of Tables 8
- GENERAL INFORMATION 9
- Version Information 10
- Related Manuals 10
- Documentation Conventions 10
- ESD Protection 11
- Recycling 12
- Regulatory Compliances 12
- Trademarks 13
- Software License 13
- Warranty 13
- PRODUCT OVERVIEW 15
- Output Quantities 16
- HMT310 Transmitter Parts 17
- Probe Options 18
- Filter Options 19
- Sensor Options 19
- INSTALLATION 21
- Transmitter Unit 22
- 0507-035 23
- Mounting the Probes 25
- 0507-024 26
- 0507-040 28
- 0507-041 30
- CAUTION 32
- Connections 33
- Power Supply Requirements 34
- OPERATION 35
- USB Connection 37
- Indicator 38
- Terminal Program Settings 39
- List of Serial Commands 40
- Measurement Output 42
- Output Reading Once 43
- Set Serial Interface Mode 43
- Serial Line Settings 43
- Output Formatting 45
- Set Time and Date 47
- Outputs 47
- Commands) 49
- Other Commands 50
- Addresses 51
- List Commands 51
- Set Result Filtering 52
- Reset Transmitter 53
- Display Error Messages 53
- Set Analog Output Mode 54
- Scale Analog Outputs 55
- Test Analog Outputs 56
- Readings 56
- Chemical Purge (Optional) 57
- Output signal 58
- Set Chemical Purge Interval 59
- Chemical Purge in Powerup 60
- Sensor Heating (Optional) 61
- Sensor Heating ON/OFF 62
- Setting Heating Parameters 62
- Example: 63
- MAINTENANCE 65
- Changing the Sensor 66
- Technical Support 67
- Product Returns 67
- CALIBRATION AND ADJUSTMENT 69
- Sensor Change 71
- Set Calibration Date 72
- Analog Output Calibration 72
- (in Two Points) 73
- Low End Adjustment 74
- High End Adjustment 75
- One Point) 76
- MPC Command Syntax 78
- Starting MI70 Adjustment 81
- Adjusting RH with MI70 82
- Adjusting T with MI70 83
- 1-point T adjustment 84
- 2-point T adjustment 84
- Environment Settings 85
- Last Adjustment Date 85
- TECHNICAL DATA 87
- 0507-021 88
- Calculated Variables 90
- Dewpoint Temperature 92
- Spare Parts and Accessories 93
- Dimensions in mm (inches) 94
- Rain Shield Dimensions 95
- 120 (4.72) 96
- 12 (0.47) 96
- Figure 26 HMT314 Dimensions 97
- Figure 27 HMT315 Dimensions 97
- Figure 28 HMT317 Dimensions 98
- Figure 29 HMT318 Dimensions 98
- PROBE INSTALLATION KITS AND 99
- INSTALLATION EXAMPLES 99
- HMT317) 100
- Cable Gland 101
- 0508-027 102
- *M210619EN* 105
Relacionado con productos y manuales para Los Componentes Del Dispositivo De Seguridad Vaisala HUMICAP HMT310
(18 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.158 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales